11.1 GENERAL PROPERTIES OF SUBSURFACE WATER
The study of surface water is incomplete without the knowledge of its interaction with subsurface water. Subsurface water comprises all water either in storage or flowing below the ground surface. There are two types of subsurface water: (1) interflow, and (2) groundwater flow. Interflow takes place in the unsaturated zone, close to the ground surface. Groundwater flow takes place in the saturated zone, which may be either close to the ground surface or deep in underground waterbearing formations. The surface separating the unsaturated and saturated zones is referred to as the groundwater table, or water table. In Section 2.4, the following three components of runoff were identified: (1) surface runoff, (2) runoff contributed by interflow, and (3) runoff contributed by groundwater, i.e., baseflow. These components depict the path of runoff. At any one time, runoff consists of a combination of the three. Generally, during wetweather periods, surface runoff and interflow are the primary contributors to runoff. Conversely, during dryweather periods, baseflow is the majorif not the onlycontributor to runoff. Traditionally, surface runoff has been regarded as the single most important component of flood flows. This approach is embodied in the concept of overland flow, or Hortonian flow, after Horton, who pioneered the theory of infiltration capacity [12]. As shown in Chapters 4 and 10, overland flow can be used to simulate runoff response. Notwithstanding the classical Hortonian approach, theories of hillslope hydrology have emphasized the role of interflow and the timingrather than the pathof runoff. Two runoff components are recognized under this framework:
Subsurface water occurs by infiltration of rainfall and/or snowmelt into the ground. Once the water has infiltrated, it can follow one of two paths:
The preferred path of subsurface flow is in a downward direction to join the saturated zone. Interflow is flow in the unsaturated zone; groundwater flow is flow in the saturated zone. The earth's crust is composed of soils and rocks containing pores (i.e., voids) that can hold air and water. The various types of soils and rocks have different relative amounts of pore space and, consequently, can hold different amounts of air and water. In subsurface water evaluations, the earth's crust is divided into two zones:
The boundary between the unsaturated and saturated zones is the water table.
The distance from the ground surface to the water table varies from place to place. In some places it may be less than 1 m, whereas in others it may be more than 100 m. In general, the water table is not flat, tending to follow the surface topography in a subdued way, deeper beneath the hills and shallower beneath the valleys. In certain cases it may even coincide with the ground surface, as with ponds and marshes, or lie slightly above it, as in the typical exfiltration to perennial streams and rivers. Extent of Groundwater Resources Although only a fraction of precipitation infiltrates into the ground, the total amount of subsurface water is far greater than the total amount of land surface water. This is because groundwater flow is characteristically a very slow process, whereas land surface water moves at comparatively faster speeds. The average residence time of surface water (i.e., the time elapsed while flowing on the earth's surface) is estimated at less than 2 wk. On the other hand, the average residence time of subsurface water has been estimated to vary between 2 wk to 10,000 yr [19] . Both surface and subsurface water are driven by the force of gravity in their unrelenting movement toward the sea. To place the relationship between surface and subsurface water amounts in the proper perspective, it is necessary to examine the world's water balance. Studies have shown that about 97 percent of all the world's water is seawater. Of the remaining 3 percent, onethird occurs in solid form in glaciers and polar ice caps, and twothirds constitutes fresh water, including surface and subsurface water. Of the total amount of fresh water, more than 99 percent is groundwater. The water stored in lakes, reservoirs, streams, rivers, the unsaturated zone below the ground surface, and in vapor form in the atmosphere accounts for only a small fraction of the total amount of fresh water [8]. About half of the groundwater is contained within 800 m of the earth's surface [20]. Not all can be used, either because of its salinity or because of the great depths at which it occurs. The distribution of groundwater varies throughout the land areas of the world. Where it does occur, it can been used to supplement surface water supplies. Furthermore, in regions with little or no surface water resources, groundwater is often the only source of fresh water.
The feasibility of extracting water from a groundwater reservoir is determined by the following three properties: (1) porosity, (2) permeability, and (3) replenishment. Porosity is the ratio of void volume to total volume of soil or rock. It is interpreted as a measure of the ability of the soil deposit or rock formation to hold water in sufficiently large quantities. Permeability describes the rate at which water can pass through a soil deposit or rock formation. Permeable materials are those that allow water to pass through them easily. Conversely, impermeable materials are those that allow water to pass through them only with difficulty or not at all. The permeability value is a function of the size of pores or voids and the degree to which they are interconnected. Replenishment relates to the size and extent of the groundwater reservoir and its connection to other surface/groundwater resources of the region. Replenishment is largely controlled by nature, although it can be affected by human activities, both positively (e.g., the artificial recharge of groundwater), and negatively (by paving formerly porous land). Aquifers An aquifer is a saturated permeable geologic formation which can yield significant quantities of water to wells and springs. By contrast, an aquiclude is a saturated geologic formation that is incapable of transmitting significant amounts of water under ordinary circumstances. The term aquitard describes the less permeable beds in a stratigraphic sequence. These beds may be permeable enough to transmit water in significant quantities, but not sufficient to justify the cost of drilling wells to exploit the groundwater resource. Most geologic formations are classified as either aquifers or aquitards, with very few formations fitting the definition of an aquiclude. Aquifer Types. Aquifers can be of two types: (1) unconfined and (2) confined. An unconfined aquifer, or water table aquifer, is an aquifer in which the water table constitutes its upper boundary. A confined aquifer is an aquifer that is confined between two relatively impermeable layers or aquitards. Unconfined aquifers occur near the ground surface; confined aquifers occur at substantial depths below the ground surface. Figure 112 shows typical configurations of confined and unconfined aquifers. The water level in an unconfined aquifer rests at the water table. In a confined aquifer, the water level in a well may rise above the top of the aquifer. If this is the case, the well is referred to as an artesian well, and the aquifer is said to exist under artesian conditions. In some cases, the water level may flow above the ground surface, in which case the aquifer is known as flowing artesian well, and the aquifer is said to exist under flowing artesian conditions.
The water level in wells located in a confined aquifer defines an imaginary surface referred to as the potentiometric surface [8]. Several wells can help establish a potentiometric contour map, a map depicting lines of equal hydraulic head in the aquifer. A potentiometric map provides an indication of the direction of groundwater flow in an aquifer. A perched aquifer is a special case of unconfined aquifer. A perched aquifer forms on top of an impermeable layer located well above the water table. Infiltrating water is held on top of this impermeable layer to form a saturated lens, usually of limited extent and not connected to the main water table. The water table of a perched aquifer is referred to as a perched water table. Recharge and Discharge. Typically, groundwater flows from a recharge area, through a groundwater reservoir, to a discharge area. The recharge area is an area of replenishment with infiltrated water. The groundwater reservoir is the main body of the aquifer. The discharge area is the area where the infiltrated water returns back to the surface. Most of the groundwater eventually returns to the surface before reaching the oceans [31]. In humid and subhumid climates, aquifer recharge usually takes place in upland slopes, with aquifer discharge occurring in the valleys, where the water table is shallow enough to be intercepted by streams and rivers. In arid and semiarid regions, however, the situation may be quite different. In this case, the water table in the valleys is usually much deeper, with aquifer recharge taking place primarily by channel transmission losses in streams and rivers. Discharge from an unconfined aquifer is accomplished in three ways. First, if the water table is close to the ground surface, water may be discharged from the aquifer either by vapor diffusion upward through the soil or through evapotranspiration by vegetation. Second, if the water table is intersected by a stream, discharge is accomplished by exfiltration. Third, an aquifer can be discharged by humaninduced means, i.e, by pumping through a well, either for agricultural, municipal, or industrial uses. Discharge from a confined aquifer is accomplished in two ways: first, by fast seepage through a permeable path in the overlying impermeable material, or by slow seepage through aquitards; and second, by humaninduced means, i.e., by well pumping as with unconfined aquifers [27].
11.2 PHYSICAL PROPERTIES OF SUBSURFACE WATER
In an unconfined aquifer, the water table is the surface at which the water pressure is exactly equal to atmospheric pressure. The soil or rock below the water table is generally considered to be saturated with water. Indeed, the water table is the upper limit of a zone of saturation, or saturated zone. The capillary fringe is located immediately above the water table. Water is held in this fringe by capillarity, at moisture levels close to saturation. However, the capillary fringe differs from the saturated zone in that a well will fill with water only to the base of the capillary fringe, i.e., the water table. Water in the capillary fringe is referred to as capillary water to distinguish it from the water in the saturated zone, or groundwater proper. The thickness of the capillary fringe varies from one rock formation to another, depending on the size of the pores, from a few millimeters to several meters. Due to natural irregularities, the top of the capillary fringe is likely to be an irregular surface, with the moisture likely to decrease gradually in a direction away from the water table. Lowering of the water table by drainage, pumping, or other means will result in a lowering of the capillary fringe. However, all water cannot be drained out of the soil or rock formation. Surface tension and molecular effects are responsible for a certain amount of water being retained in the pores against the action of gravity. Specific Yield The total amount of water in an aquifer of area A and thickness b is
in which V = total volume of water, A = surface area of the aquifer, b = aquifer thickness, and n = porosity. However, the total amount of water that will drain freely from an aquifer is
in which V_{w} = volume of freedraining water and S_{y} = specific yield, the ratio of freedraining water volume to aquifer volume. Since a certain amount of water is always retained in the pore volume, the specific yield of an aquifer is always less than its porosity. Specific retention is the ratio of volume of retained water to volume of aquifer. Therefore, the sum of specific yield and specific retention is equal to the porosity. In coarsegrained rocks with large pores, specific yield will be almost equal to the porosity, with specific retention reduced to a minimum. Conversely, in finegrained rocks, specific retention can approximate the value of porosity, with specific yield being close to zero. Above the capillary fringe is the intermediate zone, which may range in thickness from zero to more than 100 m. The water within this zone is referred to as pellicular water, with the water content generally close to specific retention. Above the intermediate zone is the upper portion of the earth's crust, referred to as the soil. The capillary fringe, the intermediate zone, and the soil are all part of the unsaturated zone. Interflow takes place in the unsaturated zone. Soil Moisture Levels Water enters the unsaturated zone by infiltration, where it is held in thin films around the solid particles or in the pore space between them. Within a given volume, the degree of saturation is a function of the relative amount of pore space that is occupied by water. The degree of saturation is a measure of the prevailing soilmoisture condition. Field Capacity. Assume that a heavy rainfall causes significant amounts of water to infiltrate into the ground. If this situation persists for a sufficiently long period, the voids will eventually fill with water, i.e., a saturated condition will be attained. During and immediately following rainfall, water will drain freely out of the soil under the effect of gravity, a characteristically slow process that can last anywhere from a few hours to several days. The total amount of water drained in this way represents the specific yield, with the remaining water constituting the specific retention. The moisture level equivalent to specific retention is the field capacity, i.e., the amount of water that can be held in the soil against the action of gravity. Following a rainy period, evaporation from soil surfaces and evapotranspiration from vegetation act together to reduce the soil moisture below field capacity, and a soilmoisture deficit is gradually developed. The soilmoisture deficit is usually expressed in terms of the rainfall depth necessary to restore the soil moisture to field capacity. Permanent Wilting Point. At or near field capacity, the water is largely held in thin films around the solid particles, with substantial amounts of air space between them. At the airwater interface, the difference in pressures (atmospheric in the air spaces and less than atmospheric within the thin films) results in a net suction effect. This suction effect, referred to as soilwater suction, keeps the water films adhered to the soil particles against the action of gravity. With continuing absence of rainfall, increasing amounts of soil water are abstracted by evaporation, evapotranspiration, and vapor diffusion. This causes the water films surrounding the solid particles to become thinner and the soilwater suction to increase. Consequently, it becomes increasingly difficult for plants to extract water from the soil. Faced with this condition, the plants respond by using less water and reducing their growth rate. Plants that are deprived of normal amounts of water for an extended period of time begin to wilt. If water does not become available within a reasonable period, the permanent wilting point is reached and the plants die. Flow Through Porous Media The soil or rock deposits through which water flows can be regarded as porous media. The fundamental law governing flow through porous media is Darcy's law. Darcy's Law. In 1856, Darcy pioneered the analysis of flow of water through sands [6]. His experiments led to the formulation of the empirical equation of flow through porous media bearing his name. With reference to Fig. 113, Darcy's law states that the flow rate Q is directly proportional to the crosssectional flow area A and hydraulic drop Δh and inversely proportional to the length Δl:
in which K is a proportionality constant known as the hydraulic conductivity. The quantity Δh/Δl is a dimensionless ratio referred to as hydraulic gradient i:
Therefore,
and
is the specific discharge or discharge per unit area, with the dimensions of velocity. The specific discharge, also known as Darcy velocity or Darcy flux, is a macroscopic concept that can be readily measured. It must be clearly differentiated from the microscopic velocities associated with the actual paths of the water as it winds its way through porous media. These velocities are real butfor all practical purposesintractable. Darcy's law is valid for groundwater flow in any direction. Given a constant hydraulic conductivity and hydraulic gradient, the specific discharge is independent of the angle θ shown in Fig. 113. This holds even for values of θ greater than 90°, when the flow is being forced up through the cylinder against gravity. Hydraulic Conductivity. The hydraulic conductivity, which according to Eq. 116 has the dimensions of velocity [LT^{ 1}], is a function of the physical properties of fluid and porous media. To illustrate, consider the experimental setup of Fig. 113. Assume two experiments, each consisting of two tests, with Δh and Δl being held constant. In the first experiment, the fluid is the same (e.g., water), and two types of porous media are tested: (1) a coarse sand and (2) a fine sand. The specific discharge of the second test (fine sand) will be smaller than that of the first test (coarse sand). In the second experiment, the porous medium is the same (e.g., coarse sand), and two fluids of different viscosity are tested: (1) water and (2) oil. The specific discharge of the second test (oil) will be smaller than that of the first test (water). An expression for hydraulic conductivity in terms of fluid and porous media properties is [13]:
in which d = mean grain diameter, ρ = fluid density, μ = fluid absolute viscosity, g = gravitational acceleration, and C = a dimensionless constant, a function of porous media properties other than mean grain diameter, i.e., grain size distribution, sphericity and roundness of the particles, and the nature of their packing. Intrinsic Permeability. In Eq. 117, the product Cd ^{2} is a function only of the porous media, whereas ρ and μ are functions of the fluid. Therefore,
in which k is the specific, or intrinsic, permeability. From Eqs. 117 and 118,
Intrinsic permeability is expressed in square centimeters or, alternatively, in darcys. One darcy unit is defined as the intrinsic permeability that produces a specific discharge of 1 cm/s, using a fluid of absolute viscosity equal to 1 centipoise, under a hydraulic gradient that results in the term ρgi being equal to 1 atm/cm. One darcy is approximately equal to 10^{8} cm^{2}. Equation 119 establishes a clear distinction between hydraulic conductivity K and intrinsic permeability k. However, it should be noted that hydraulic conductivity is often referred to as coefficient of permeability, whereas intrinsic permeability is commonly referred to as permeability. The different units, centimeters per second in the case of hydraulic conductivity, and square centimeters (or darcys) in the case of intrinsic permeability, may be used to avoid confusion. Variability of Hydraulic Conductivity. Soil and rock formations in which hydraulic conductivity is independent of position are said to be homogeneous. Conversely, formations in which hydraulic conductivity is a function of position are said to be heterogeneous. The formation is said to be isotropic if, at a given point, the hydraulic conductivity is independent of the direction of measurement. On the other hand, if the hydraulic conductivity varies with the direction of measurement, the formation is said to be anisotropic at that point. The four possible combinations of homogeneity, heterogeneity, isotropy, and anisotropy are shown in Fig. 114. Most sedimentary rocks are anisotropic with respect to hydraulic conductivity because the individual particles are not spherical, but they tend to be elongated in a direction parallel to the bedding. This causes the hydraulic conductivity to be greater in a direction parallel to the bedding than in a direction perpendicular to it. Measured hydraulic conductivities vary by several orders of magnitude. A formation with hydraulic conductivity of 1 m/d would generally be regarded as permeable and likely to be a good aquifer. Conversely, a formation with hydraulic conductivity of less than 10^{3} m/d would generally be regarded as impermeable and, therefore, not a good aquifer. However, depending on the intended application, comparisons of hydraulic conductivity (or permeability) are relative. For instance, a formation that is too impermeable for use as an aquifer may at the same time be too permeable for use as a water barrier in the foundation and core of an earth dam.
Compressibility. Both fluid (water) compressibility and medium (aquifer) compressibility affect groundwater flow. Assume that an increase in pressure leads to a decrease in volume of a given mass of water. The water compressibility is defined as
in which β = water compressibility, V_{w} = volume of a given mass of water, and ΔV_{w} = change in volume caused by a Δp change in pressure. For practical applications, β may be considered to be a constant, since it changes very little over the range of fluid pressures normally encountered in practice. The accepted value of β is 4.4 × 10^{10} m^{2}/N (Pa^{1}). The compressibility of porous media is quite different from the compressibility of water. Assuming that the compressibility of individual soil grains is negligible, porous media can only be compressed by rearrangement of the soil particles into a tighter packing. The total stress on the media is borne partly by the solid particles forming the granular skeleton and partly by the fluid in pore spaces. The portion of total stress that is borne by solid particles is called the effective stress. Rearrangement of the soil particles is caused by changes in the effective stress and not by changes in total stress. The compressibility of porous media is defined as
in which α = compressibility of porous media, V_{T} = total volume of the soil mass, and ΔV_{T} = change in volume caused by a Δσ_{e} change in effective stress. The value of α is a function of soil type. Clays have typical α values in the range of 10^{6} to 10^{8} m^{2}/N; sands, 10^{7} to 10^{9} m^{2}/N; gravel, 10^{8} to 10^{10} m^{2}/N; sound rock, 10^{9} to 10^{11} m^{2}/N [8] . Note that water compressibility is of the same order of magnitude as that of the less compressible geologic materials. Specific Storage, Transmissivity, and Storativity. Six basic physical properties of fluid (i.e., water) and porous media (soil and rock formation) are needed for the description of saturated groundwater flow; three for the fluid and three for the medium. The water properties are density ρ, absolute viscosity μ, and compressibility β. The porous media properties are porosity n, intrinsic permeability k, and compressibility α. All other parameters describing hydrogeologic properties are based on these; see, for example, the definition of hydraulic conductivity, Eq. 119. Specific storage of a confined aquifer is defined as the volume of water released per unit volume of aquifer per unit decrease in hydraulic head. Compressibility considerations lead to the following expression for specific storage [8]:
in which S_{s} = specific storage in L ^{1} units. The transmissivity of a confined aquifer is defined as follows:
in which T = transmissivity [L^{2}T ^{1} units], K = hydraulic conductivity [LT ^{1}units], and b = aquifer thickness [L units]. In SI units, the transmissivity is given in square meters per second. A transmissivity greater than 0.015 m^{2}/s is indicative of a good aquifer, suitable for water well exploitation. The storativity of a confined aquifer is defined as
in which S = storativity, a dimensionless value. Typical values of storativity vary in the range 0.005 to 0.00005. Given the definition of specific storage, large decreases in hydraulic head over extensive formations are required in order for a confined aquifer to yield substantial amounts of water. In unconfined aquifers, the concept of specific yield is equivalent to the storativity of confined aquifers. Typical values of specific yield vary in the range 0.01 to 0.30. The higher values of specific yieldas compared to storativityreflect the fact that releases from an unconfined aquifer represent an actual dewatering of the pore spaces. On the other hand, releases from confined aquifers represent only the secondary effect of aquifer compaction caused by changes in fluid pressure. The favorable yield properties of unconfined aquifers make them more suited to well exploitation. 11.3 EQUATIONS OF GROUNDWATER FLOW
Depending on whether the flow is steady or unsteady, and saturated or unsaturated, the equations of groundwater flow can be formulated in one of the following three ways:
Equations for steadystate and transient saturated flow are described here. See [8] for details on transient unsaturated flow through porous media. SteadyState Saturated Flow The law of conservation of mass for steadystate flow through saturated porous media requires that the net fluid mass flux through a control volume be equal to zero, i.e., the inflow must equal the outflow. This leads to the equation of continuity:
in which the quantities v are specific discharges in three orthogonal directions x, y, and z, respectively. Assuming fluid incompressibility, ρ(x, y, z) is constant, and consequently it can be eliminated from Eq. 1115. Substitution of Darcy's law in Eq. 1115 yields:
in which the quantities K and i are hydraulic conductivities and hydraulic gradients, respectively. For an isotropic medium, K_{x} = K_{y} = K_{z} = K. For a homogeneous medium, K(x, y, z) is constant, and it can be eliminated from Eq. 1116. Given i_{x} = ∂h/∂x, i_{y} = ∂h/∂y, and i_{z} = ∂h/∂z, in which h = hydraulic head, Eq. 1116 reduces to:
Equation 1117 is the Laplace equation. The solution of this equation is a function h(x, y, z) describing the value of hydraulic head at any point in a threedimensional flow field. For twodimensional flow, the third term on the left side of Eq. 1117 cancels out, and the solution is a function h(x, y). Transient Saturated Flow The law of conservation of mass for transient flow through saturated porous media requires that the net fluid mass flux through a control volume be equal to the time rate of change of fluid mass storage within the control volume. Therefore, the equation of continuity, Eq. 1115, is modified to
Assuming that the fluid is incompressible, ρ(x, y, z) is constant, and it can be eliminated from
For an isotropic medium, K_{x} = K_{y} = K_{z} = K. For a homogeneous medium, K(x, y, z) is constant. The time rate of change of porosity can be related to time rate of change of hydraulic head by the following:
Therefore, Eq. 1119 reduces to [14, 15]:
Equation 1121 is a diffusion equation, with K/S_{s} being the hydraulic diffusivity of the aquifer [L^{2}T ^{1} units]. The solution of this equation is a function h(x, y, z, t) describing the value of hydraulic head in three dimensions at any time. It requires the knowledge of S_{s} and K or, alternatively, the basic fluid and aquifer properties ρ, μ, α, n, k, and β. For the special case of a horizontal confined aquifer of thickness b, the third term on the left side of Eq. 1121 drops out, and with Eqs. 1113 and 1114:
The solution of this equation is a function h(x, y, t) describing the value of hydraulic head in two dimensions at any time. It requires the knowledge of aquifer storativity S and transmissivity T. The ratio T/S is the hydraulic diffusivity of the aquifer. 11.4 WELL HYDRAULICS
Well hydraulics describes groundwater flow problems involving discharge to wells. There is a wealth of literature on the subject, including Bear [1], U.S. Bureau of Reclamation [26], and Walton [28]. The classical problem of radial flow to a well is described in this section. Radial Flow to a Well Consider an aquifer with the following characteristics:
Furthermore, assume for simplicity: (1) a single pumping well, (2) a constant pumping rate, (3) negligible well diameter relative to the aquifer's horizontal dimensions, (4) well penetration through the entire aquifer depth, and (5) uniform initial hydraulic head throughout the aquifer. In horizontal and vertical coordinates, Eq. 1122 is the governing equation for this problem, its solution being a function h(x, y, t). The idealized nature of this problem justifies the assumption of radial symmetry. A sketch of aquifer, pumping well, observational well, and potentiometric surface is shown in Fig. 115. The conversion of Eq. 1122 into radial coordinates, using r = (x^{2} + y^{2})^{1/2}, leads to [15]:
in which r is the radial distance from the pumping well to the observational well.
The solution of Eq. 1123 is a function h(r, t ) describing the potentiometric surface. The uniform initial hydraulic head is h_{0}. For convenience, solutions are often expressed in terms of drawdown, the difference between uniform initial hydraulic head and potentiometric surface:
in which Z = drawdown, h_{0} = uniform initial hydraulic head, and h = hydraulic head (i.e., potentiometric surface elevation). The assumption of uniform initial hydraulic head throughout the aquifer leads to the following initial condition:
for r ≥ 0. Furthermore, assuming no change in hydraulic head at r = ∞, the following boundary condition is obtained:
for t ≥ 0. Theis Solution The solution of Eq. 1123 subject to the given initial and boundary conditions is due to Theis [23]:
in which Q = (constant) pumping rate [L ^{3}T ^{1} units], T = aquifer transmissivity [L ^{2}T ^{1} units], and u is a dimensionless variable defined as
with r = radial distance from pumping well to observational well, S = aquifer storativity (dimensionless), and t = time. With u defined by Eq. 1128, the integral in Eq. 1127 is referred to as the well function W(u), applicable to homogeneous isotropic confined aquifers with fulldepth well penetration and at constant pumping rate. Values of W(u) as a function of u are shown in Table 111. Equation 1127 reduces to
Two types of problems can be solved by the Theis method: (1) prediction and (2) identification. In the prediction problem, the pumping rate Q, radial distance r, aquifer transmissivity T, and storativity S are known, and the variation of observational well drawdown Z with time t is sought. In the identification problem, the pumping rate Q, radial distance r, and observational well drawdown versus time data (Z versus t) are known, and the aquifer properties S and T are sought.
The prediction problem can be solved directly with Eqs. 1128 and 1129.
For any assumed time t, u is calculated with Eq. 1128 and used to obtain W(u) from Table 111.
Then, Z is calculated with A variation of the prediction problem is that of the calculation of the cone of depression, or drawdown cone, as shown in Fig. 115. In this case, the pumping rate Q and aquifer properties (storativity S and transmissivity T) are known, and the variation of drawdown Z with radial distance r is sought at a fixed time t. For any assumed radial distance r, u is calculated with Eq. 1128 and used to obtain W(u) from Table 111. Then, Z is calculated with Eq. 1129 for the assumed radial distance r and fixed time t. The identification problem is solved by a graphical procedure. Eliminating T from Eqs. 1128 and 1129 leads to
which indicates that the ratio Z /t is proportional to the ratio W(u)/(1/u). The solution is accomplished by the following steps:
For a given radial distance, drawdown increases with increasing time. For a given time, drawdown decreases with increasing radial distance. For a given time and radial distance, drawdown is directly proportional to pumping rate. For a given time, distance, and pumping rate, drawdown is inversely proportional to transmissivity and storativity. Other conditions being constant, low transmissivity results in deep drawdown cones of limited extent, whereas high transmissivity results in shallow cones of wide extent. Likewise, an aquifer of low storativity has a comparatively deeper drawdown cone than an aquifer of high storativity [8].
For a detailed discussion of other types of radial flow to a well or wells, including unconfined aquifers, varying pumping rates, multiplewell configurations, and partially penetrating wells, see [8] and [28].
11.5 SURFACESUBSURFACE FLOW INTERACTION
The interaction between surface and subsurface flow is central to the study of stream types and baseflow recession. Surface flow occurs in the form of overland flow in the catchments and, subsequently, streamflow in the channel network. Subsurface flow occurs as interflow in the unsaturated zone and as groundwater flow in the saturated zone. The contribution of subsurface water to surface water is a function of stream type. Depending on whether streams serve as discharge or recharge areas for aquifers, they are classified as (1) effluent, or gaining streams, or (2) influent, or losing streams. Effluent streams are discharge areas for aquifers. Usually, an aquifer is intersected by the effluent stream, discharging into it. This type of aquifer discharge is distributed along the stream length, in contrast to aquifer discharge that occurs at a point, i.e., a spring. The distributed discharge to effluent streams is referred to as exfiltration, or baseflow, and is typical of humid and subhumid environments where aquifers are at relatively shallow depth. Influent streams are recharge areas for aquifers, largely due to the high permeability of their channel beds. This type of aquifer rechargeknown as channel transmission loss(es) in stream channel routingis distributed along the stream length and is typical of streams in arid and semiarid regions. Depending on whether they flow all year, a few days of the year, or seasonally, streams can be further classified as (1) perennial, (2) ephemeral, or (3) intermittent (Section 2.4). Perennial streams are those that flow throughout the year, during both wet and dry weather. Their dry weather flow is largely baseflow, i.e., discharge from groundwater reservoirs. Unlike perennial streams, ephemeral streams are those that flow only in wet weather, i.e., during and immediately following rainfall. In the southwestern United States, ephemeral streams are known as arroyos, washes, or dry washes, and flow approximately 30 d per year on the average. Typically, perennial streams are effluent, whereas ephemeral streams are influent. Furthermore, it is common for ephemeral streams to abstract most or all of their wetweather flow through channel transmission losses. Intermittent streams are those possessing mixed characteristics, discharging either to or from groundwater reservoirs. Surface Runoff and Streamflow Generation Streamflow consists of a combination of surface and subsurface runoff, which can be extremely complex in certain cases. Surface runoff is generated by a gamut of surface and nearsurface flow processes, of which some of the most important are:
Hortonian overland flow [12] describes the process that takes place when rainfall rate exceeds infiltration capacity, usually at the beginning of a storm (or season), when the soil profile is likely to be on the dry side. Saturation overland flow describes the process that takes place after the soil profile has become saturated, either from antecedent rainfall events or from a sufficient volume of rainfall within the same event. At this point, any additional rainfall, regardless of intensity, will be converted into surface runoff. Saturation overland flow usually occurs during an infrequent storm, or toward the end of a particularly wet season, when the soil is likely to be already wet from prior storms. Throughflow prevails in heavily vegetated areas with thick soil covers containing less permeable layers, overlying relatively impermeable unweathered bedrock [16]. Throughflow takes place as interflow, or as lateral flow immediately below the ground surface. The concept of partialarea runoff developed from the recognition that runoff estimates were improved by assuming that only rainfall on a small and fairly constant part of each drainage basin is able to contribute to direct runoff [16]. Thus, partialarea runoff can be interpreted as a combination of throughflow in the upper hills lopes and saturation overland flow in the lower hillslopes [10, 11, 29]. Direct channel interception refers to the runoff that originates from rainfall falling directly into the channels. This mode of streamflow generation may be important in dense channel networks and certain humid basins. Surface phenomena includes processes such as crust development, hydrophobic soil layers, and frozen ground, which render the soil surface impermeable, promoting surface runoff and streamflow. For instance, a surface crust may develop following splash erosion in a denuded watershed, adversely affected by human activities or a natural hazard such as fire. Under a specific set of circumstances, including soil type and texture, the silt entrained by splash erosion may deposit on the surface and create a thin crust that eventually reduces the infiltration rate to a negligible level. This mode of surface runoff and streamflow generation is typical of semiarid environments, where surface runoff may take place even though the underlying soil profile, below a relatively thin veneer, remains substantially dry [17, 25]. Hillslope Hydrology and Streamflow Generation Hillslope hydrology refers to the hydrologic processes taking place on hillslopes. These processes are intrinsically related to streamflow generation. An important question is whether the preferred path of runoff is on the surface, as overland flow, or through the subsurface, by subsurface stormflow, or interflow. Several theories of hillslope hydrology have been developed, together constituting a spectrum of plausible processes and models [5]. They range from Hortonian theory [12] to throughflow theory [16]. Hortonian theory emphasizes Hortonian overland flow, whereas throughflow theory focuses on interflow processes. Hortonian overland flow is applicable to poorly vegetated slopes with relatively thin soil covers. Throughflow is more apt to explain the processes that take place in heavily vegetated areas with thick permeable soil layers. Between these two extremes lie a variety of models in which runoff is assumed to consists of a mix of Hortonian overland flow, and unsaturated and saturated throughflow. The partialarea concept is a combination of throughflow in the upper hillslopes and overland flow in the lower hillslopes (Fig. 117). Based on field studies, Freeze and Cherry [8] have concluded that most surface runoff hydrographs in humid, vegetated basins originate from not more than 10 percent of the catchment area, and then, are likely to prevail in only 10 to 30 percent of the storms. Betson [2], among others, has documented a substantial improvement in runoff predictions by using the partialarea concept. The size of partial areas is a function of storm depth, rainfall intensity, and antecedent moisture conditions. As a percentage of the total catchment, partial areas in the Southern Appalachians were shown to vary between 5 percent for lighttomoderate storms and 40 percent for heavy storms [2]. With deforestation, the percentage can amount to 80 percent or more. Generally, partial areas may be expected to vary between 5 percent and 20 percent of the total basin [22].
Refinements of the partialarea concept have led to the variablesourcearea model of hillslope hydrology [21, 24]. These variablesource areas are envisioned as comprising lowlying lands adjacent to streams and rivers and concentrated near watershed outlets [3, 7]. Variations in the extent of source areas are dictated by antecedent soil moisture conditions, soilmoisture storage capacity, and rainfall intensity. When the upper soil horizon is saturated, both throughflow and overland flow occur, with eventual exfiltration to stream banks. According to this scheme, the variablesourcearea can be interpreted as an expanded stream system, which helps explain the growth in drainage density experienced by small watersheds under heavy rainfall [4]. The variablesourcearea model is a dynamic version of the partialarea concept. This dynamism is manifested in soil moisture and runoff changes occurring annually, seasonally, between storms, and during storms. The source areas are largely responsible for overland flow, whereas the remainder of the watershed acts primarily as a reservoir to provide baseflow and to maintain saturation of the source areas [7]. The variablesourcearea model visualizes the average storm hydrograph as consisting of (1) rain falling directly onto the channel, and (2) water transmitted rapidly through wet soil adjacent to the stream. The source areas shrink and expand as a function of rainfall amounts and antecedent soilmoisture conditions. In the absence of rainfall, streams are fed to a large extent by moisture moving downslope under unsaturated flow conditions. This downward migration favors the quick release of water from the source areas into the channels during storms. Typical storm hydrographs reflecting the variablesourcearea concept are shown in Fig. 118.
Hydrograph Separation and Baseflow Recession The variablesourcearea concept has led to increased emphasis on the timing of runoff during and immediately following a storm. This justifies the separation of runoff into two components: (1) quickflow, consisting of fast interflow (subsurface stormflow), overland flow, and rain falling directly on the channels, and (2) baseflow, consisting of slow interflow and groundwater flow. Hydrograph separation is an established procedure of hydrologic analysis (Section 5.3). It has an important role not only in flood hydrology but also in groundwater hydrology. In flood hydrology, it serves as a means to quantify the relationship between quickflow and baseflow. In groundwater hydrology, it provides information on the nature and behavior of local and regional groundwater regimes. Baseflow Recession. Consider the streamflow hydrograph shown in Fig. 119. Flow varies throughout the year, with peaks of approximately 100 m^{3}/s and lows of about 1 m^{3}/s. The smooth line is the baseflow hydrograph or baseflow curve, reflecting the seasonally varying groundwater contributions. The ragged line is the streamflow hydrograph, reflecting the relatively fast response typical of steep catchments with shallow soils of low permeability.
The recession portion of the baseflow curve usually plots as a straight line (or a series of straight lines) on semilogarithmic paper, with discharge plotted on the log scale, as shown in Fig. 119. This leads to an equation of the form
in which Q = baseflow at any time t after the starting time t_{o}, Q_{o} = baseflow at t_{o}, and t_{s} = a recession constant known as the time of storage, defined as the time required for the flow Q to recede to 0.368 Q_{o} (i.e., for t = t_{s}, Q = Q_{o} e^{1}).
Other forms of baseflow recession equations are:
in which α, β, t_{s} and K are recession constants. The values α and β are positive, and K is generally less than 1. Plotting Eqs. 1133 to 1137 on semilogarithmic paper, with discharge on the logarithmic scale, yields a straight line. From Eqs. 1133 and 1137, the relationship between t_{s} and K is
which leads to
The integration of Eq. 1139 between a time corresponding to Q_{o} and a time corresponding to Q leads to:
in which S = storage volume released from groundwater [L ^{3} units]. Combining Eqs. 1138 and 1140:
The volume under the recession curve (from Q_{o} to Q) can be calculated by assuming that as t → ∞, A historical perspective of baseflow recessions is given by Hall [9].
Bank Storage.
A concept closely related to baseflow recession is that of bank storage.
In the upland reaches, subsurface contributions to streamflow generally aid in the buildup of the flood wave.
In the lower reaches, however, bank storage may contribute to flood wave attenuation.
As shown in
QUESTIONS
PROBLEMS
REFERENCES

Documents in Portable Document Format (PDF) require Adobe Acrobat Reader 5.0 or higher to view; download Adobe Acrobat Reader. 